Beyer & Otto GmbH
Beyer & Otto GmbH
Germany
Kardinal-Faulhaber-Str. 10
63801 Kleinostheim
Phone: +49 (0)6027 6044 Fax: +49 (0)6027 9553
www:
www.beyer-otto.de
Kardinal-Faulhaber-Str. 10
63801 Kleinostheim
Phone: +49 (0)6027 6044 Fax: +49 (0)6027 9553
Contact:
Contact languages:
German, English
- Manufacturer
- Trader
- Service provider
- Supplier
Flow Gun - Pneumatic gun
Type TS-215/G Flow Gun for Hotmelt Glues
This model is electrically heated and was engaged pneumatically
Flowing pistol for this process of aluminum corrie Indian inks (ca.300ml).
You can work also vertically up (over head).
The temperature is adjusted over a bimetal thermometer. This one
Temperature range is located at the underside this one between 30-200 ° C.
Pistol is an opening in which a slit hull is.
If this is turned clockwise by means of screwdriver,
the temperature increases in the top-hat. This is at a thermometer
at the pistol back readable.
A filing is part of the pistol with a pressure inferior valve and one
Manometers adjusting and for this reading the end pressing pressure. One
an extensive nozzle assortment is deliverable. A thermofuse
overheating the adhesive prevents.
For work without interruptions the use of this one is
Corrie Indian ink in front of being warm equipment (KVG 2 or KVG 4) recommend.
Specifications
Technical data
Heating range: 30° - 200° C
Heating-up time: 20 - 50 min
Air consumption: approx. 30 l/min at 4 bar
Weight: ca.1900gr.
Connection: 230/115 V, 50-60 Hz
Heating power: 400 watts
Flow rate: 60 g/min max.
Working pressure: 1 - 6bar
Type TS-215/G Flow Gun for Hotmelt Glues
This model is electrically heated and was engaged pneumatically
Flowing pistol for this process of aluminum corrie Indian inks (ca.300ml).
You can work also vertically up (over head).
The temperature is adjusted over a bimetal thermometer. This one
Temperature range is located at the underside this one between 30-200 ° C.
Pistol is an opening in which a slit hull is.
If this is turned clockwise by means of screwdriver,
the temperature increases in the top-hat. This is at a thermometer
at the pistol back readable.
A filing is part of the pistol with a pressure inferior valve and one
Manometers adjusting and for this reading the end pressing pressure. One
an extensive nozzle assortment is deliverable. A thermofuse
overheating the adhesive prevents.
For work without interruptions the use of this one is
Corrie Indian ink in front of being warm equipment (KVG 2 or KVG 4) recommend.
Specifications
Technical data
Heating range: 30° - 200° C
Heating-up time: 20 - 50 min
Air consumption: approx. 30 l/min at 4 bar
Weight: ca.1900gr.
Connection: 230/115 V, 50-60 Hz
Heating power: 400 watts
Flow rate: 60 g/min max.
Working pressure: 1 - 6bar
- Manufacturer
- Trader
- Service provider
- Supplier
- Manufacturer
- Trader
- Service provider
- Supplier
Processing equipment for hot waxes: TS170/HWS
Hot wax (or hard wax) is used for the dull-gloss surface treatment of furniture, stairs, floors, walls and ceilings. The areas of application are: cabinet making (furniture, parquet and cork flooring) - woodworking operations - prefabricated house manufacturers - interior finishing of buildings etc.
To avoid work breaks - caused by heating up the cartridge - an additional cartridge preheating unit ( KVG-2 and KVG-4), suitable for 2 cartridges, is used. This enables you to work free of interruption.
Special features:
The wax is sealed airtight in the aluminium cartridge (content 200 g).
No drying-out of the wax in the cartridge or gun.
Cleaning is dispensed with.
Hot oil can also be sprayed using returnable cartridges.
One cartridge is sufficient for approx. 15 to 20 sq. mtrs.
Very good spray pattern. The atomization is achieved
The hot wax does not contain any solvents !
It can be sprayed at any angle and even vertically upwards (overhead)
Hot wax (or hard wax) is used for the dull-gloss surface treatment of furniture, stairs, floors, walls and ceilings. The areas of application are: cabinet making (furniture, parquet and cork flooring) - woodworking operations - prefabricated house manufacturers - interior finishing of buildings etc.
To avoid work breaks - caused by heating up the cartridge - an additional cartridge preheating unit ( KVG-2 and KVG-4), suitable for 2 cartridges, is used. This enables you to work free of interruption.
Special features:
The wax is sealed airtight in the aluminium cartridge (content 200 g).
No drying-out of the wax in the cartridge or gun.
Cleaning is dispensed with.
Hot oil can also be sprayed using returnable cartridges.
One cartridge is sufficient for approx. 15 to 20 sq. mtrs.
Very good spray pattern. The atomization is achieved
The hot wax does not contain any solvents !
It can be sprayed at any angle and even vertically upwards (overhead)
Products and services
Company information
About Us
We are specialised in the development and manufacture of qualitatively high-value appliances for the application of sealing compounds, hot-melt adhesives and hot waxes. The appliances are conceived for the professional user. We are widely independent of sub-contracting suppliers and very flexible due to our very high share of own-production (light-metal foundry, press room, welding unit, NC and CNC automatic machines, pre- and final assembly, etc. - all in our own works). We react immediately to changing market, conditions and customer´s wishes. We differentiate ourselves from our competitors, in that, amongst other things, apart from three complete product ranges (=standard products), we offer custom-made solutions to problems at short notice.
The company B & O is extraordinarily active in innovation and is export-orientated (approx. 40 % of our annual production goes amongst other places to Western Europe, Japan, USA and Australia).
Our supreme principle is quality at sensible prices. Our customers, amongst which all renowned manufactures of sealing compounds, hot-melt adhesives and hot waxes are counted, value this attitude. The maintenance of delivery times and optimal customer service are self-evident for us.
We are constantly interested in making new business contacts on the basis of mutual trust and would be delighted to be able to win you as a partner.
Export markets
Worldwide
The company B & O is extraordinarily active in innovation and is export-orientated (approx. 40 % of our annual production goes amongst other places to Western Europe, Japan, USA and Australia).
Our supreme principle is quality at sensible prices. Our customers, amongst which all renowned manufactures of sealing compounds, hot-melt adhesives and hot waxes are counted, value this attitude. The maintenance of delivery times and optimal customer service are self-evident for us.
We are constantly interested in making new business contacts on the basis of mutual trust and would be delighted to be able to win you as a partner.
Export markets
Worldwide
