Weld Seam Inspection  Manufacturers, Traders, Suppliers

• Stillstands- und Revisionsarbeiten
• Montagen und Demontagen
• 24 Stunden Rufbereitschaft an 365 Tagen
• Laufende Instandhaltung
• Schweißarbeiten in WIG, MIG, MAG, E-Hand, Spiegelschweißen, Gasschweißen
• Durchführung der behördlich erforderlichen Abnahmen wie Vorprüfung der Zeichnungsunterlagen, Bau- und Druckprüfung

• Rohrleitungsvorfertigung in der Werkstatt
• Rohrleitungsmontagen
• Reparatur von Rohrleitungssystemen
• Schweißarbeiten in WIG, MIG, MAG, E-Hand, Spiegelschweißen und Gasschweißen
• Bereitstellung der erforderlichen Dokumentation
• Beistellung der erforderlichen Materialien und deren Vorfertigung
• Lieferung von Ersatzteilen

• Teilweise- und komplette Kesselkomponentenfertigung
• Walzen, Kanten, Blechbearbeitung
• Dreh- und Fräsarbeiten
• Oberflächenbearbeitung und Schweißnahtbehandlung durch Strahlanlage
• Rohrleitungsbau und Rohrbiegearbeiten
• Verkauf und Bereitstellung von technischen Gasen

• Biomasseheizkraftwerke
• Müllverwertungsanlagen
• Werkstoffrecyclinganlagen
• Stahlbau und Metallbau
• Rohr- und Anlagenbau
• Chemische Industrie
• Industrieanlagen
• Schiffsbau
• Lebensmittelindustrie
• Turbinenbau

• AD 2000 - Merkblatt HP0, TRD 201, DIN EN 12952, DIN EN 12953 und AD 2000 Merkblatt HP100R
• DIN EN ISO 3834-3
• DIN 18800-7 Klasse D
• Schweißfachingenieurdienstleistungen, Internationaler Schweißfachmann
• Magnetpulverprüfung (MT) nach DIN EN ISO 9712
• Eindringprüfung (PT) nach DIN EN ISO 9712
• Sichtprüfung (VT) nach DIN EN ISO 9712
• Begutachtungen von Schweißverbindungen an Stählen
• Befähigte Person zur Durchführung von Prüfungen an Druckbehältern und Rohrleitungen
• Schweißer MIG/MIG, MAG, E-Hand, Spiegelschweißen, Gasschweißen

• Acetylen
• Argon
• Corgon
• Sauerstoff
• Treibgas
• Ballongas
• etc.

Standards and ASME
We test according to DIN and ASME or all similar standards for all non-destructive testing such as RT, UT, MT, PT and VT according to ASME BOILER AND PRESSURE VESSEL CODE, Section V, Article 2,5,6,7&.lt;br>
Inspections

• Construction and weld seam monitoring and weld seam inspection
• Plant inspections
• Inspection of piping systems

Non-destructive material testing in our own test centre or directly at your premises
Our spectrum ranges from incoming and outgoing inspections and checks of dimensional accuracy to quality assurance accompanying series production and special test procedures.
Inspections

• Construction and welding seam monitoring
• Plant inspections
• Testing of piping systems

Testing systems - Accredited according to 17025:2005

• X-ray [RT]Mobile X-ray systems and isotopes are equipped for every application. There is also a large X-ray bunker available.
• Ultrasound and Phased Array [UT]With the most modern phased array technology, we also inspect your parts on site.
• crack detection [PT/MT]For this purpose, electromagnetic testing devices - direct and alternating current are used (test bench, yoke magnet). For the PT-testing of mass-produced parts a self-designed system is available.
• Visual control [VT]The data from the endoscope can be stored directly on the laptop.
• Leak test / leakage test [LT]The complete equipment for helium test, leakage tests can be carried out at our factory as well as at your site.
• Spectral analysis and confusion check [PMI]With the most modern technology we can carry out material determination and analysis.
• Mobile Hardness Measurement [HT]
• ferrite measurement [FT]
• Roughness measurement [Ra]Roughness measurement on material and weld seam via ferrite scopes.

• Wall thickness determinationWall thickness determination
• coating thickness measurementLayer thickness measurement via ultrasound

Ultrasonic Testing uses high frequency sound energy to examine components. Possible uses are flaw detection/characterization, precision measurements and material categorization.

Surpasses the quality delivered by manual ultrasonic scanning, which has lost favor due to inferior Probability Of Detection (POD) results. Most ultrasonic testing equipment is now semi-automatic or fully-automatic and produces an electronic record of the inspection, leading to a marked increase in POD. Electronic records can ensure code compliance, facilitate detailed audit, improve inspection integrity and most importantly promote customer confidence in the inspection method.

At Applus RTD, we have an extensive range of ultrasonic testing tools and techniques to match every inspection challenge, from simple thickness measurement to fully automated inspections.

testing systems:

• X-ray [RT]: Mobile X-ray systems and isotopes are equipped for every application. In addition, a large X-ray bunker is available. strong>