12 companies for Manual Plate Shears ✓ B2B manufacturers, distributors & suppliers from 3 countries ✓ With special service for fast information and prices ✓
Filter:
Description
The Excenter Sheet Shears are used for nearly all cutting problems. The basic machine is suited even for the smallest sheet-metal-workshop. The machines work ridge-free and distortion-free and enable nearly powerless cutting.
Features of the machines:
- Hold-down device with hard rubber rail to protect polished sheets
- Supporting table with extensions
- Manual back gauge 500 mm
- Groves every 10 mm over the whole table, parallel to the lower blade
- All-steel blade, double-edged
- Angle gauge, left and right
The machines are available in different sizes.
Technical data
Capacity: 1,00 / 1,25 / 1,5 / 2,0 mm
Useful lengths: 1.030 / 1.530 / 2.030 / 2.530 / 3.030 mm
Cutting angles: 1,5 / 1,8 / 2, 2 / 2,9 / 4,0 °
For detailed information please contact [email protected].
Areas of application
Show more WELDING SEAM PREPARATION SHEET METAL PROCESSING PIPE PROCESSING GUILLOTINE SHEARS
- Manual Plate Shears | Section Shears | Table Shears
9536 Schwarzenbach, Switzerland Brändle Werkzeugmaschinen GmbH Trader ✓ Service provider ✓
Company Profile Send enquiry
- Manual Plate Shears | Plate Shears | Steel Shears
- Manual Plate Shears | Shears | Single Ring Scissors
- Manual Plate Shears | Plate Shears
09356 Kuhschnappel, Germany Hammer Industrieanlagen und Werkzeugmaschinen Vertrieb GmbH Trader ✓ Service provider ✓
Company Profile Send enquiry
- Manual Plate Shears | Section Shears | Cold Profile Shears
99096 Erfurt, Germany HME Erfurt GmbH Manufacturer ✓ Trader ✓ Service provider ✓
Company Profile Send enquiry
- Manual Plate Shears | Engine Sheet Shears | Table Shears
- Manual Plate Shears | Plate Shears
- Manual Plate Shears | Table Shears
79713 Bad Säckingen, Germany So Sondermaschinen Vertriebs GmbH Manufacturer ✓ Trader ✓ Supplier ✓
Company Profile Send enquiry
- Manual Plate Shears | Shears | Plate Shears
- Manual Plate Shears | Shears | Plate Shears
About us
Our company has existed since 1946.
At that time, it was founded by Mr. Stückmann from Aue.
Together with Mr. Hillen, he built up the company over the years.
In 1998, the company was taken over by Mr. Jürgen Hase, Mr. Hans-Jürgen Kragl and Mr. Andreas Pilz as a limited company.
Since then, all products have been constantly innovatively developed and modernized.
Today, the company is managed by Andreas Pilz alone.
At that time, it was founded by Mr. Stückmann from Aue.
Together with Mr. Hillen, he built up the company over the years.
In 1998, the company was taken over by Mr. Jürgen Hase, Mr. Hans-Jürgen Kragl and Mr. Andreas Pilz as a limited company.
Since then, all products have been constantly innovatively developed and modernized.
Today, the company is managed by Andreas Pilz alone.
Manual Plate Shears - Manufacturers, Traders & Suppliers
No time for research on Manual Plate Shears? Just fill out our special service form.
IndustryStock searches for your company the suitable manufacturers, dealers or service providers for Manual Plate Shears and sends your mail immediately to these companies.
Are you looking for Manual Plate Shears?
Are you looking for Manual Plate Shears. IndustryStock's product and service search engine will not only help you find relevant results for Manual Plate Shears but also related products and services. All contact information of listed Manual Plate Shears manufacturers, traders, suppliers and dealers are freely available to all users.
How do you rate the information on this page?
15 Reviews 92%